Daniel Barnaby

Urban N-core (Northbrook site) primary operator
Thermo Partisol 2000i / 2025i PM 2.5 FRM:
Ensured sample media (PM 2.5 filters) were handled, transported, and stored according to federal rules and best practices. Installed sample runs and set up the sampler according to the EPA 3-day sample schedule. Collected the samples within the required 7 days 9 hours. Recorded sample data and any issues on the fly sheet (a Chain of Custody form). Sometimes transported the sample filters to CCDES for post-weighing.
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed twice-monthly maintenance and verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet. Regularly cleaned and maintained the PM 10 head and PM 2.5 cutter.

Teledyne T640x / T640:
Assisted in setting up the enclosure and installing the sampler.
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed install, removal, and twice-monthly verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet.

Met One Super SASS:
Ensured sample media (Nylon and Teflon filters in cassettes) were handled, transported, and stored according to federal rules and best practices. Installed sample runs and set up the sampler according to the EPA 3-day sample schedule. Collected the samples. Recorded sample data and any issues on the Chain of Custody (COC) form. Packed the SASS and URG samples and shipped them to contractors RTI or Wood Laboratories.
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed monthly maintenance and verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet.

URG 3000-N:
Ensured sample media (quartz filters in a cassette) were handled, transported, and stored according to federal rules and best practices. Installed sample runs and set up the sampler according to the EPA 3-day sample schedule. Collected the samples. Recorded sample data and any issues on the COC form. Packed the SASS and URG samples and shipped them to contractors RTI or Wood Laboratories.
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed monthly maintenance and verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet.

Teledyne T400NV ozone:
Installed the monitor and performed install verification using a Teledyne T700U dilution calibrator, Teledyne T701 or Sabio 1001 zero air generator. Reported the results to the Data Unit.
Investigated and diagnosed the source of any problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Regularly inspected the unit when at the site to help ensure no issues went unaddressed.
Performed annual sample line change. Ensured line material and length, and the resulting sample flow met EPA rules and best practices.

Teledyne T100U SO2 trace level:
Installed the monitor and performed install verification using a Sabio 2010 dilution calibrator, Sabio 1001 zero air generator, and SO2 cylinder. Reported the results to the Data Unit.
At the instruction of the Air Lab, performed re-span and re-zero when necessary.
Investigated and diagnosed the source of any problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Regularly inspected the unit when at the site to help ensure no issues went unaddressed.
Performed an in-line filter change every two weeks, recorded pre- and post-change data to ensure the procedure was done correctly.
Performed annual sample line change. Ensured line material and length, and the resulting sample flow met EPA rules and best practices.

Thermo 48iQTL CO trace level:
Installed the monitor and performed install verification using a Sabio 2010 dilution calibrator, Sabio 1001 zero air generator, and CO cylinder. Reported the results to the Data Unit.
At the instruction of the Air Lab, performed re-span and re-zero when necessary.
Investigated and diagnosed the source of any problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Regularly inspected the unit when at the site to help ensure no issues went unaddressed.
Performed an in-line filter change every two weeks, recorded pre- and post-change data to ensure the procedure was done correctly. At the instruction of the Data Unit, manually ran post-change datalogger autocal to re-zero the unit.
Performed annual sample line change. Ensured line material and length, and the resulting sample flow met EPA rules and best practices.

Thermo 42i-Y NOy:
Installed the monitor and performed install verification using a Sabio 2010D dilution calibrator, Sabio 1001 zero air generator, and NO cylinder. Reported the results to the Data Unit.
Regularly inspected the unit when at the site to help ensure no issues went unaddressed.
Performed annual sample line change. Ensured line material and length, and the resulting sample flow met EPA rules and best practices.

Maintained site documents required by EPA and IEPA including QAPPs, SOPs, and manuals.

PAMS program primary operator
Markes / Agilent AutoGC:
Analyzed and interpreted the complex technical and scientific data, instructions, and requirements associated with completing system assembly, setup, and operation. Served as liaison to contractors Agilent, Markes, and Orsat as we finished assembling the AutoGC, calibrating and operating the system, and making improvements. System status and data output were analyzed to detect and solve problems and to improve system performance. Performed troubleshooting to determine the cause of problems and issues, and implemented solutions including some repairs and component replacements. Inspected the unit regularly for anything out of the ordinary. Performed regular system maintenance including changing helium cylinders, filling the hydrogen generator reservoir with DI water, and replacing the in-line filters / dessicants.
Operated and worked with all AutoGC system components: Agilent 7890B, Markes Unity-xr, Markes Kori-xr, Markes CIA Advantage-xr, Parker TOC-1250, Parker H2PEMPD Hydrogen Gas Generator, Gast compressor, Gast sample pumps, KNF sample pump.

ATEC 8000 carbonyl sampler:
Ensured sample media (cartridges) were handled, stored, and shipped according to federal rules and best practices. Installed sample runs and set up the sampler according to the EPA 3-day sample schedule. Collected the samples within the required 72-hours. Recorded sample data and any issues on the COC form.
Investigated the source of any problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed preseason, postseason, and monthly verifications using the Alicat FP-25 flow meter. Assisted Quality Assurance (QA) personnel in developing a standard operating procedure (SOP) performing the verifications.
Annually, arranged for the sampler to be recertified by ERG. Removed and shipped the sampler to ERG, received and reinstalled the unit upon its return, and ensured proper paperwork was onsite incompliance with EPA rules.
Performed regular replacement of the sampler's ozone denuder. Requested the replacement part from the Air Lab, performed the replacement onsite, and shipped the removed denuder for laboratory analysis.
Performed annual sample line change. Ensured line material and length, and the resulting sample flow met EPA rules and best practices.

Teledyne T500U direct-measure NO2:
Installed the monitor and performed install verification using a Teledyne T700U dilution calibrator, T701 zero air generator, and NO cylinder. Reported the results to the Data Unit.
Regularly inspected the unit when at the site to help ensure no issues went unaddressed.
Performed annual sample line change. Ensured line material and length, and the resulting sample flow met EPA rules and best practices.

Kipp & Zonen SMP6-V pyranometer and SUV5-V UV ensors:
Installed and leveled the sensors according to EPA rules and regulations. Replaced instrument cables when necessary. Performed field verifications using the spare / calibration set of instruments.

Vaisala CL-51 ceilometer:
Assisted with unit installation and setup. Regularly cleaned the glass over the lens. Performed troubleshooting when needed.

Met One 370D precipitation gauge:
Assisted with unit installation and setup. Perform preseason and midseason tests of the unit's function and connectivity. Performed troubleshooting when needed.

Analyzed and interpreted the PAMS Technical Assistance Documents (TAD), PAMS QAPP, SOPs, and manuals to ensure compliance with federal and state regulations pertaining to the PAMS program. Checked PAMS sample freezer temperature and regularly compared with Alicat FP-25 standard.

Participated in the PAMS workgroup monthly meetings with operators from around the country, EPA, and contractors such as Battelle and Orsat.

NATTS program primary operator
Andersen / Tisch PUF:
Ensured sample media (PUF medium and filter) were handled, stored, and shipped according to federal rules and best practices. Installed sample runs and set up the sampler according to the EPA 6-day sample schedule. Collected the samples within the mandated 72-hours. Recorded sample data and any issues on the Chain of Custody (COC) form.
Measured the required ambient temperature and barometric pressure using an Alicat FP-25 flow meter.
Investigated the source of any problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed monthly maintenance and verifications using a PUF orifice flow standard, and reported the results to the Data Unit via Excel spreadsheet.

Andersen / Tisch PM10 high-volume metals:
Ensured sample media (quartz filters) were handled and stored according to federal rules and best practices. Installed sample runs and set up the sampler according to the EPA 6-day sample schedule. Collected the samples. Recorded sample data and any issues on the COC form and filter envelope. Returned samples to CCDES for post-sample weighing. Beginning in 2025, shipped samples directly to ERG regularly for metals analysis.
Investigated the source of any problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed monthly maintenance and verifications using a Hi-vol orifice flow standard, and reported the results to the Data Unit via Excel spreadsheet.

VOC / air toxics using ERG(C):AT sampler:
Ensured sample media (canister) were handled, stored, and shipped according to federal rules and best practices. Set up canister runs and tested for leaks according to the EPA 6-day sample schedule. Recorded sample data and any issues on the COC form. Returned the sample canister to ERG for analysis.
Investigated the source of any problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.

Carbonyls using ERG(C):AT sampler:
Ensured sample media (cartridges) were handled, stored, and shipped according to federal rules and best practices. Set up carbonyl runs and tested for leaks according to the EPA 6-day sample schedule. Recorded sample data and any issues on the COC form. Returned the samples to ERG for analysis.
Investigated the source of any problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed quarterly verifications using the Alicat FP-25 flow meter.

Additional duties and responsibilities

Utilized the site datalogger to place the monitors in and out of maintenance, to gather ambient temperature information, and to perform other functions related to the monitor and site.

Analyzed and interpreted the NATTS Technical Assistance Documents (TAD), NATTS QAPP, SOPs, and manuals to ensure compliance with federal and state regulations pertaining to the PAMS program. Checked NATTS sample freezer temperature and regularly compared with Alicat FP-25 standard. Contacted ERG personnel regarding any problems that were identified, and to arrange for annual sampler replacement.

Primary shipping and receiving contact / liaison to contract laboratory ERG for the following parameters: PAMS carbonyl, NATTS PUF, NATTS VOC, NATTS carbonyl. Coordinated storage of received sample media and distribution to sampling sites. Coordinated shipping of collected samples to ERG. Primary shipping and receiving contact / liaison to contract laboratories Wood and RTI. Performed all of the above for SASS and URG speciation parameters.

Participated in EPA Technical Systems Audits (TSA) in 2022 and 2025, and the NATTS and PAMS TSA in 2023. This involved checking and updating all of the site documents, interviews with EPA and contractor Battelle, and follow up meetings to discuss findings and recommendations.

Served as liaison to various contractors such as those installing electrical service on the lower roof of the Northbrook water plant and another performing HVAC maintenance and repair in our lab room.

While continuing to perform my duties as an EPS III, I performed the following:

Oversaw a "reset" period of greater field staff accountability to management. Was the first point of contact for operators who were now sending more emails and messages, and making more calls about their plans for the day, situations that came up during the course of their work, and plans to be absent or late.

Led meetings with various members of the field staff to arrange site coverage for absent team members, to hear questions and concerns, and to answer them.

Led Thermo Partisol 2025i sequential FRM training with the North Region operators.

Led Teledyne T640x FEM training with the North Region operators.

Made a plan with the field staff to recover the ozone equipment from the field and return it to the Air Lab during the first week of November. The plan was a success.

Attended the 2025 Technical Systems Audit site visits in the North and am scheduled to attend follow up meetings in December.

Assisted two members of the field staff with FMLA absences, served as liaison between them and Human Resources, and provided other assistance.

Reviewed 2026 PAMS and NATTS contracts and made meaningful changes. Served as liaison between EPA Region 5 and IEPA field staff and Data Unit to discuss the contracts and plan for next year.

Served as a main point of contact for the Air Monitoring 2025 internal inventory.

Approved timecards, absences, and overtime. Provided guidance regarding the appropriate use of certain time codes, and drafting a proper overtime request.

Served as liaison between IEPA Air Monitoring and TechLaw Consultants, Inc. to arrange PEP and through-the-probe audits at several sites.

Approved several invoices for mowing at our sites in the South and Central regions.

Served as liaison to ComEd in order to sort out the multiple meter situation at the Schiller Park site. The situation was resolved.

Made lists of sites that are missing equipment such as ladders. Made lists of equipment or supplies that are needed by operators and will be ordered. Made a list of keys everyone has and who is missing which.

Performed various Air Monitoring duties by assignment at the following sites:
McCook, Kennedy Near Road, Evanston, Zion, Cary, Love's Park, Rockford.

Duties and responsibilities
Thermo Partisol / R&P 2000i PM 2.5 FRM:
Ensured sample media (PM 2.5 filters) were handled, transported, and stored according to federal rules and best practices. Installed sample runs and set up the sampler according to the EPA 3-day and 6-day sample schedules. Collected the samples within the required 7 days 9 hours. Recorded sample data and any issues on the fly sheet (a Chain of Custody form). Sometimes transported the sample filters to CCDES for post-weighing.
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed twice-monthly maintenance and verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet. Regularly cleaned and maintained the PM 10 head and PM 2.5 cutter.

Met One BAM 1020:
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed twice-monthly maintenance and verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet. Regularly cleaned and maintained the PM 10 head and PM 2.5 cutter.
Replaced the filter tape when necessary. Thoroughly cleaned the inside of the unit of filter tape lint.

Thermo 5014i FEM:
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed twice-monthly maintenance and verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet. Regularly cleaned and maintained the PM 10 head and PM 2.5 cutter.
Replaced the filter tape when necessary. Thoroughly cleaned the inside of the unit of filter tape lint.

Teledyne T400 ozone:
Installed the monitor and performed install verification using a Thermo 49i transfer standard. Reported the results to the Data Unit.
Investigated and diagnosed the source of any problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Regularly inspected the unit when at the site to help ensure no issues went unaddressed.
Performed annual sample line change. Ensured line material and length, and the resulting sample flow met EPA rules and best practices.
Performed an in-line filter change every two weeks, recorded pre- and post-change data to ensure the procedure was done correctly.
Utilized the site datalogger to place the monitor in and out of maintenance, to gather ambient temperature information, and to perform other functions related to the monitor and site.

Teledyne T500U direct-measure NO2:
Installed the monitor and performed install verification using a Teledyne T700U dilution calibrator, T701 zero air generator, and NO cylinder. Reported the results to the Data Unit.
Regularly inspected the unit when at the site to help ensure no issues went unaddressed.
Performed annual sample line change. Ensured line material and length, and the resulting sample flow met EPA rules and best practices.

Teledyne T640:
Assisted in setting up the enclosure and installing the sampler.
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed install, removal, and twice-monthly verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet.

Performed various Air Monitoring duties by assignment at the following sites:
McCook, Kennedy Near Road, Evanston, Zion, Cary, Love's Park, Rockford.

Duties and responsibilities
Thermo Partisol / R&P 2000i PM 2.5 FRM:
Ensured sample media (PM 2.5 filters) were handled, transported, and stored according to federal rules and best practices. Installed sample runs and set up the sampler according to the EPA 3-day and 6-day sample schedules. Collected the samples within the required 7 days 9 hours. Recorded sample data and any issues on the fly sheet (a Chain of Custody form). Sometimes transported the sample filters to CCDES for post-weighing.
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed twice-monthly maintenance and verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet. Regularly cleaned and maintained the PM 10 head and PM 2.5 cutter.

Met One BAM 1020:
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed twice-monthly maintenance and verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet. Regularly cleaned and maintained the PM 10 head and PM 2.5 cutter.
Replaced the filter tape when necessary. Thoroughly cleaned the inside of the unit of filter tape lint.

Thermo 5014i FEM:
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed twice-monthly maintenance and verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet. Regularly cleaned and maintained the PM 10 head and PM 2.5 cutter.
Replaced the filter tape when necessary. Thoroughly cleaned the inside of the unit of filter tape lint.

Teledyne T400 ozone:
Installed the monitor and performed install verification using a Thermo 49i transfer standard. Reported the results to the Data Unit.
Investigated and diagnosed the source of any problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Regularly inspected the unit when at the site to help ensure no issues went unaddressed.
Performed annual sample line change. Ensured line material and length, and the resulting sample flow met EPA rules and best practices.
Performed an in-line filter change every two weeks, recorded pre- and post-change data to ensure the procedure was done correctly.
Utilized the site datalogger to place the monitor in and out of maintenance, to gather ambient temperature information, and to perform other functions related to the monitor and site.

Teledyne T500U direct-measure NO2:
Installed the monitor and performed install verification using a Teledyne T700U dilution calibrator, T701 zero air generator, and NO cylinder. Reported the results to the Data Unit.
Regularly inspected the unit when at the site to help ensure no issues went unaddressed.
Performed annual sample line change. Ensured line material and length, and the resulting sample flow met EPA rules and best practices.

Teledyne T640:
Assisted in setting up the enclosure and installing the sampler.
Investigated and diagnosed the source of any leaks, problems or issues, developed appropriate solutions, and reported findings to management and Air Lab personnel. Inspected the unit regularly for anything out of the ordinary.
Performed install, removal, and twice-monthly verifications using the Alicat FP-25 flow meter, and reported the results to the Data Unit via Excel spreadsheet.

Care One Pharmacy is a delivery pharmacy whose clients are long term care, hospice, and skilled nursing facilities. They provide medications and medical supplies to the residents of these facilities. As a Lead Data Entry Technician, I processed medication orders that arrived electronically, verbally, or by fax. I typed the details of these orders accurately into the patient's profile. I took note of any irregularities present in the orders, and followed up with the facility, prescriber, or pharmacist to resolve them. I solved problems with orders that I and others had entered at the request of the pharmacists. I frequently partnered with members of the billing department to help solve pharmacy coverage issues.

Many of our facilities received their medication in "pill rolls" - individually packaged time-and-date-stamped doses that make it easy for caregivers to administer drug therapies. As a Lead Data Entry Technician, I set up the pill roll files used by the Fill Technicians to create the rolls using the TCGRx system. This is a long and complicated process with many opportunities for error, and required high accuracy and attention to detail, as well as knowledge of potential mistakes that must be avoided. I also performed troubleshooting of problems with rolls that I and others had programmed.

I was frequently required to convert units of measure. This allowed the entering of prescriptions for intravenous antibiotics, and for proper dosing with stock medications of different concentrations.

I had additional responsibilities due to my role as a Lead Data Entry Technician. I assisted in training new technicians, particularly the pill roll process. I helped prioritize the workload. Care One is a 24/7 operation and has a complicated delivery schedule. I watched for high-priority orders and either processed them right away or delegated them to others. I interviewed candidates for open positions and followed up with management to discuss their applications, interviews, and skills.